Cobalt-Free Driers for Alkyd Coatings: Manganese, Zirconium, Cerium and Iron Compared

November 19, 2026 · Technical

Why formulators are replacing cobalt

Cobalt octoate and cobalt naphthenate remain the most efficient primary driers for oxidative alkyd curing. The pressure to replace them is regulatory and reputational rather than a performance failure:

  • Cobalt metal carries a harmonised CLP classification — Carc. 1B (H350), Muta. 2, Repr. 1B, Resp. Sens. 1 and Skin Sens. 1 — under index 027-001-00-9 in Annex VI.
  • Five cobalt(II) salts (sulfate, dichloride, dinitrate, carbonate and diacetate) have been on the REACH Candidate List since 2008 because of their carcinogenic and reprotoxic properties.
  • Cobalt octoate (CAS 136-52-7) and cobalt naphthenate (CAS 61789-51-3) have no harmonised classification of their own and are not among those five Candidate List salts. They are self-classified substances — a distinction that is routinely lost in customer questionnaires, and one worth explaining rather than hiding.

For completeness: no cobalt compound is currently on REACH Annex XIV (the Authorisation List), so the issue for most customers is classification, SDS wording and substitution policy — not authorisation.

Primary, secondary and the balance between them

Alkyd films cure by autoxidation: the resin's unsaturated fatty-acid chains absorb oxygen, form hydroperoxides, and decompose into radicals that cross-link the film. Primary driers catalyse that decomposition. Secondary driers do not catalyse oxidation; they coordinate with carboxylic acid groups on the resin and raise cross-link density, which shows up as hardness, adhesion and faster hard-dry.

Replacing cobalt is therefore not a one-for-one swap. You are replacing the primary catalyst and, in most cases, re-tuning the secondary part of the package at the same time.

DrierRoleStrengthsWatch-outs
Manganese octoate / naphthenatePrimaryClosest drop-in for cobalt; strong through-dry; lower cost; widely availableCan darken white and light-tint systems; more prone to surface skinning; strong oxidiser — keep away from peroxides
Zirconium octoateSecondaryHardness, adhesion and early film strength; works well with Ca and with MnNot a standalone replacement — it needs a primary drier in the package
Cerium octoatePrimary (oxidation catalyst)Cobalt-free; useful in high-solids and waterborne alkyds; no cobalt labellingHigher cost; drying response varies considerably with resin and acid value — must be trialled
Iron complexes (proprietary)PrimaryVery fast through-dry; marketed as cobalt-freeYellowing/discolouration risk in light colours; ligand chemistry is supplier-specific — do not substitute by metal content alone

How much to dose

Start from the metal-on-binder-solids basis, not from product weight. As a working range, total primary metal is usually 0.02–0.15 % on resin solids, with secondary metals roughly 1.5–4× the primary level — but the useful figure comes from your own drying curve, not from a table. Measure set-to-touch, tack-free, hard dry and through-dry at your plant's temperature and humidity, and record the film thickness each time.

Two practical rules: keep the primary-to-secondary ratio constant while you screen candidates, and change one variable per trial. Manganese or iron at the same metal loading as cobalt will usually dry faster at the surface and may skin in the can, which is why the first adjustment is often the anti-skinning level, not the drier level.

Colour and yellowing

Cobalt driers are notorious for yellowing in whites during dark storage, and manganese is not immune — it can brown. Iron-based systems are the most colour-sensitive. If the application is a white or pastel decorative coating, screen for colour development over 7–14 days in the dark as well as after UV exposure, and consider a cerium- or manganese-based package with a hindered-amine or UV-absorber combination rather than assuming an iron complex will be invisible.

What to ask a supplier

  • Metal content on the COA (titrated), not just the product name — a manganese drier is sold at 6 %, 8 % and 10 % Mn.
  • Carrier acid and solvent: 2-ethylhexanoate (octoate) and naphthenate behave differently in aliphatic versus aromatic let-down.
  • Batch COA and a retained sample from the batch you receive.
  • Current SDS and a statement of CLP classification for the specific product — not for cobalt metal.

Our drier range includes cobalt octoate, cobalt naphthenate, manganese octoate, manganese naphthenate, zirconium octoate and cerium octoate. If you are rebalancing a cobalt-free package, see also how to read a paint drier specification and drier troubleshooting.

Need a Chemical Supplier You Can Trust?

Reply within 12 working hours · COA & MSDS with every shipment

Request a Quote